eNauka - pregled
Pregled prema Autor Baralić, Jelena
Prikaz rezultata 1 do 20 od 72
sledeće >
| Godina | Naslov | Autor(i) | Tip rezultata | Mp-kat. |
|---|---|---|---|---|
| 2011 | Abrasive material for abrasive water jet cutting and their influence on cut surface quality | Janković, Predrag   ; Radovanović, Miroslav ; Baralić, Jelena | Konferencijski rad | Mp kategorija će biti prikazana naknadno. |
| 2018 | Analysis of Influence of Depth of Cut on Cutting Temperature in Milling in Software Advantedge | Mitrović, Anđelija ; Kovač, Pavel; Baralić, Jelena Č. ; Kulundžić, Nenad | Konferencijski rad | Mp kategorija će biti prikazana naknadno. |
| 2019 | Application of new technologies for demilitarization ordnancein order to protect environment | Đurić, Stefan D. ; Nedić, Bogdan P. ; Malbašić, Slobodan; Baralić, Jelena | Konferencijski rad | Mp kategorija će biti prikazana naknadno. |
| 2009 | Centerless grinding and polishing of circular stainless steel tubes | Radonjić, Snežana; Baralić, Jelena ; Sovilj-Nikić, Ivan | Article | Mp. category will be shown later |
| 2025 | Connection between the dynamic character of the cutting force and machined surface in abrasive waterjet machining | Baralić, Jelena ; Petrovic Savic, Suzana ; Koprivica, Branko ; Djuric, Stefan | Article | 22M22 |
| 2011 | Cut quality in abrasive water jet cutting | Janković, Predrag ; Radovanović, Miroslav ; Baralić, Jelena | Konferencijski rad | Mp kategorija će biti prikazana naknadno. |
| 2018 | Cutting speed and laser power influence on macined surface roughness and depth of the laser milling | Nedić, Bogdan P. ; Jelena Baralić ; Đurić, Stefan D. | Conference Paper | Mp. category will be shown later |
| 2021 | Defining parameters for laser cutting parts made of AISI 4140 | Mitrović, Anđelija ; Bralović, Nikola; Baralić, Jelena ; Stakić, Aleksandra ; Radović, Maja | Conference Paper | Mp. category will be shown later |
| 2013 | Effect of machining parameters on jet lagging in abrasive water jet cutting | Vlatko Marušić; Baralić, Jelena ; Nedić, Bogdan ; Željko Rosandić | Article | 22M22 |
| 2013 | Effect of machining parameters on jet lagging in abrasive water jet cutting,Utjecaj parametara obrade na zaostajanje mlaza kod rezanja abrazivnim mlazom vode | Marušić, V.; Baralić, J. ; Nedić, B.; Rosandić, Ž. | Article | 22M22 |
| 2013 | Effect of traverse speed and operating pressure on surface roughness in abrasive water jet machining | Baralić, Jelena ; Janković, Predrag ; Nedić, Bogdan | Conference Paper | Mp. category will be shown later |
| 2019 | Effect of traverse speed on cut frontgeometry in abrasive water jet machining | Baralić, Jelena ; Janković, Predrag ; Popović, Marko | Article | 52M52 |
| 2014 | Energija i kvalitet obrade abrazivnim vodenim mlazom | Baralić, Jelena | Doctoral theses | 70M70 |
| 2023 | Enhancing production efficiency through modeling | Janković, Predrag Lj. ; Baralić, Jelena ; Petković, Dušan | Conference Paper | Mp. category will be shown later |
| 2012 | Experimental determination of chip compression ratio during counterboring | Radonjić, Snežana ; Kovač, Pavel ; Slavković, Radomir ; Dučić, Nedeljko ; Baralić, Jelena | Article | 22M22 |
| 2021 | EXPERIMENTAL INVESTIGATION OF THE INFLUENCE OF MACHINING PARAMETERS ON CUT QUALITY IN MDF LASER CUTTING | Jelena Baralić ; Bogdan Nedić | Conference Paper | Mp. category will be shown later |
| 2022 | Flank wear as a function of cutting time | Baralić, Jelena ; Mitrović, Anđelija ; Radović, Maja | Conference Paper | Mp. category will be shown later |
| 2008 | Focusing tube wear and quality of the machined surface of the abrasive water jet machining | Baralić, J. ; Nedić, B.; Marušić, V. | Article | Mp. category will be shown later |
| 2016 | Geometrija reza pri obradi abrazivnim vodenim mlazom | Baralić, Jelena ; Nedić, Bogdan | Conference Paper | Mp. category will be shown later |
| 2025 | Implementation and Evaluation of Machine Learning Algorithms in Ball Bearing Fault Detection | Stepanić, Pavle ; Dučić, Nedeljko ; Vidaković, Jelena ; Baralić, Jelena ; Popović, Marko | Article | 23M23 |