Researchers
Trajković, Isaak
Results 41-60 of 77
| Issue Date | Title | Author(s) | Type | Мp-cat. |
|---|---|---|---|---|
| 2022 | Development and design of a two-armed robot from the aspect of mechatronics | Ilić, Uroš   ; Joksimović, Aleksandra ; Đurović, Marko; Veg, Emil ; Trajković, Isaak | Conference Paper | Mp. category will be shown later |
| 2022 | Additive manufacturing and characterisation using digital image correlation of tensile pipe ring specimens | Trajković, Isaak ; Milošević, Miloš ; Sedmak, Aleksandar ; Rakin, Marko ; Radosavljevic, Zoran; Mladenović, Goran ; Međo, Bojan | Conference Paper | Mp. category will be shown later |
| 2022 | Low-cycle fatigue testing setup for Additively manufactured 316L stainless steel material | Jevtić, Ivana ; Milovanović, Aleksa ; Mladenović, Goran ; Milošević, Miloš ; Trajković, Isaak | Conference Paper | Mp. category will be shown later |
| 2022 | Novel Method for Measurement of Pipeline Materials Fracture Resistance-Examination on Selective Laser Sintered Cylindrical Specimens | Trajković, Isaak ; Milošević, Miloš ; Travica, Milan ; Rakin, Marko ; Mladenović, Goran ; Kudrjavceva, Ljudmila ; Međo, Bojan | Article | 22M22 |
| 2022 | Experimental determination of flexural strength on cylindrical and plate samples produced by additive manufacturing from ABSX material | Trajković, Isaak ; Joksimović, Aleksandra ; Ilić, Uroš ; Djurović, Marko; Lukić, Tijana; Lazarević, Jovana; Milošević, Miloš | Conference Paper | Mp. category will be shown later |
| 2022 | Mechanical characteristics of parts obtained by sls printing technology | Jevtić, Ivana ; Mladenović, Goran ; Milošević, Miloš ; Milovanovic, Aleksa; Trajković, Isaak ; Travica, Milan | Conference Paper | Mp. category will be shown later |
| 2022 | Investigation of Thermal and Dimensional Behavior of 3D Printed Materials Using Thermal Imaging and 3D Scanning | Golubović, Zorana ; Travica, Milan ; Trajković, Isaak ; Petrović, Aleksandar ; Mišković, Žarko ; Mitrović, Nenad | Conference Paper | Mp. category will be shown later |
| 2022 | Significance of designing the filling of an open rapid sand filter when removing impurities from water | Đurović, Marko; Joksimović, Aleksandra ; Ilić, Uroš ; Veg, Emil ; Trajković, Isaak | Conference Paper | Mp. category will be shown later |
| 2022 | Experimental Evaluation of Hoop Stress–Strain State of 3D-Printed Pipe Ring Tensile Specimens | Travica, Milan ; Mitrović, Nenad ; Petrović, Aleksandar ; Trajković, Isaak ; Milošević, Miloš ; Sedmak, Aleksandar ; Berto, Filippo | Article | 21M21 |
| 2022 | PIPE RING TENSILE SPECIMENS STRAIN MEASUREMENT | Travica, Milan ; Mitrović, Nenad ; Petrović, Aleksandar ; Trajković, Isaak ; Milošević, Miloš ; Sedmak, Aleksandar ; Berto, Filippo | Conference Paper | Mp. category will be shown later |
| 2022 | Dimensional accuracy of parts obtained by SLS technology | Jevtić, Ivana ; Mladenović, Goran ; Milošević, Miloš ; Milovanović, Aleksa ; Trajković, Isaak ; Travica, Milan | Article | 22M22 |
| 2022 | Laser sintered polyamide specimens - fabrication and tensile testing conditions on different geometries | Trajković, Isaak ; Milošević, Miloš ; Travica, Milan ; Rakin, Marko ; Jevtić, Ivana ; Sedmak, Aleksandar ; Međo, Bojan | Conference Paper | Mp. category will be shown later |
| 2022 | Development of methodologies for experimental analysis of neck deformations caused by impact forces in martial arts | Milošević, Miloš ; Trajković, Isaak ; Golubović, Zorana ; Ivanov, Toni ; Mladenović, Goran M. ; Milovanović, Aleksa ; Mitrović, Nenad | Article | 22M22 |
| 2022 | Determining fracture mechanics parameters using the digital image correlation method on cylindrical samples produced by different additive manufacturing techniques | Trajković, Isaak ; Milošević, Miloš ; Travica, Milan ; Rakin, Marko ; Jevtić, Ivana ; Sedmak, Aleksandar ; Medjo, Bojan | Conference Paper | Mp. category will be shown later |
| 2022 | Additively manufactured tensile ring-shaped specimens for pipeline material fracture examination - influence of geometry | Trajković, Isaak ; Milošević, Miloš ; Rakin, Marko ; Sedmak, Aleksandar ; Međo, Bojan | Article | Mp. category will be shown later |
| 2022 | Removal of the As(V) and Cr(VI) from the Water Using Magnetite/3D-Printed Wollastonite Hybrid Adsorbent | Popović, Mina ; Veličković, Zlate S. ; Bogdanov, Jovica ; Marinković, Aleksandar D. ; Luna, Mariano Casas; Trajković, Isaak ; Obradović, Nina ; Pavlović, Vladimir | Article | 22M22 |
| 2022 | Influence of printing parameters on the eligibility of plane-strain fracture toughness results for PLA polymer | Milovanović, Aleksa ; Golubović, Z. ; Trajković, Isaak ; Sedmak, Aleksandar ; Milošević, Miloš ; Valean, E.; Marsavina, Liviu | Conference Paper | Mp. category will be shown later |
| 2022 | COMPARISON OF FRACTURE MECHANICS PARAMETERS DURING TESTING OF SENT SPECIMENS MADE BY DIFFERENT ADDITIVE PRODUCTION TECHNIQUE | Trajković, Isaak ; Milošević, Miloš ; Sedmak, Aleksandar ; Rakin, Marko ; Marsavina, Liviu; Medjo, Bojan | Conference Paper | Mp. category will be shown later |
| 2022 | Crack path direction in plane-strain fracture toughness assessment tests of quasi-brittle PLA polymer and ductile PLA-X composite | Milovanović, Aleksa ; Milošević, Miloš ; Trajković, Isaak ; Sedmak, Aleksandar ; Razavi, Mohammad Javad; Berto, Filippo | Conference Paper | Mp. category will be shown later |
| 2022 | Experimental determination of mechanical properties of cylindrical samples made by additive technology | Joksimović, Aleksandra ; Trajković, Isaak ; Montanari, Matteo; Milošević, Miloš | Conference Paper | Mp. category will be shown later |