Researchers
Radovanović, Miroslav
Results 161-180 of 219
| Issue Date | Title | Author(s) | Type | Мp-cat. |
|---|---|---|---|---|
| 2013 | Optimization of ANN models using different optimization methods for improving CO2 laser cut quality characteristics | Madić, Miloš   ; Radovanović, Miroslav ; Manić, Miodrag ; Trajanović, Miroslav | Article | 23M23 |
| 2013 | Pareto based optimization of laser cut quality characteristics | Madić, Miloš ; Velibor Marinković ; Radovanović, Miroslav | Conference Paper | Mp. category will be shown later |
| 2013 | Prediction model for depth of separation line obtained in CO2 laser cutting of stainless steel | Madić, Miloš ; Petković, Dušan ; Radovanović, Miroslav | Article | Mp. category will be shown later |
| 2013 | Quality of cut in plasma arc cutting | Nedić, Bogdan ; Radovanović, Miroslav ; Janković Marko | Article | 53M53 |
| 2012 | Optimizing cutting parameters based on specific cutting energy in turning using Taguchi method | Radovanović, Miroslav | Conference Paper | Mp. category will be shown later |
| 2012 | Evaluation of ANN-BP and ANN-GA models performance in prediction mechanical properties and machinability of cast coper alloys | Radenković, Goran ; Miroslav Radenković ; Miloš Madić | Article | 23M23 |
| 2012 | Investigation into the effect of the cutting parameters on the burr height in CO2 laser nitrogen cutting of AISI 304 stainless steel | Madić, Miloš ; Radovanović, Miroslav | Article | 23M23 |
| 2012 | Surface roughness of glass parts when engraving with abrasive air jet | Laurentiu Slatineanu; Margareta Coteata; Radovanović, Miroslav ; Stefan Potarniche; Lorelei Gherman; Irina Besliu | Article | 53M53 |
| 2012 | Software prototype for optimization and control of manufacturing processes | Madić, Miloš ; Kovačević, Marko M. ; Velibor Marinković ; Radovanović, Miroslav | Article | 23M23 |
| 2012 | Cost optimization of abrasive water jet cutting | Radovanović, Miroslav | Conference Paper | Mp. category will be shown later |
| 2012 | Abrasive water jet cutting with pressure of 600 MPa | Radovanović, Miroslav | Conference Paper | Mp. category will be shown later |
| 2012 | Laser Cutting Machines for 3-D Thin Sheet Parts | Radovanović, Miroslav R. | Article | Mp. category will be shown later |
| 2012 | Predictive Models of Traverse Rate in Abrasive Water Jet Cutting Based on RA and GA | Radovanović, Miroslav R. ; Janković, Predrag ; Madić, Miloš J. | Article | Mp. category will be shown later |
| 2012 | Correlation between Surface Roughness Characteristics in CO2 Laser Cutting of Mild Steel | Madić, Miloš ; Radovanović, Miroslav ; Nedić, Bogdan | Article | Mp. category will be shown later |
| 2012 | Effect of process parameters on cutting ability in abrasive water jet machining | Janković, Predrag ; Radovanović, Miroslav | Conference Paper | Mp. category will be shown later |
| 2012 | Modeling and optimization of CO2 laser cutting of stainless steel using RSM and GA | Madić, Miloš ; Radovanović, Miroslav ; Nedić, Bogdan | Article | Mp. category will be shown later |
| 2012 | Uticaj parametara obrade na specifičnu energiju rezanja kod uzdužnog struganja čelika Č.1531 | Radovanović, Miroslav | Article | 53M53 |
| 2012 | Mathematical modeling and optimization of surface roughness in turning of polyamide based on artificial neural network | Madic, Milos J ; Marinkovic, Velibor ; Radovanovic, Miroslav R | Article | 22M22 |
| 2012 | Analysis of the heat affected zone in CO2 laser cutting of stainless steel | Madić, Miloš ; Radovanović, Miroslav | Article | 22M22 |
| 2012 | Optimization of surface roughness when turning polyamide using ANN-IHSA approach | Madić, Miloš ; Radovanović, Miroslav ; Marković, Danijel S. | Article | Mp. category will be shown later |