Researchers
Radovanović, Miroslav
Results 181-200 of 220
| Issue Date | Title | Author(s) | Type | Мp-cat. |
|---|---|---|---|---|
| 2012 | Effect of process parameters on cutting ability in abrasive water jet machining | Janković, Predrag   ; Radovanović, Miroslav | Conference Paper | Mp. category will be shown later |
| 2012 | Modeling and optimization of CO2 laser cutting of stainless steel using RSM and GA | Madić, Miloš ; Radovanović, Miroslav ; Nedić, Bogdan | Article | Mp. category will be shown later |
| 2012 | Analysis of the heat affected zone in CO2 laser cutting of stainless steel | Madić, Miloš ; Radovanović, Miroslav | Article | 22M22 |
| 2012 | Cost optimization of abrasive water jet cutting | Radovanović, Miroslav | Conference Paper | Mp. category will be shown later |
| 2012 | Surface roughness of glass parts when engraving with abrasive air jet | Laurentiu Slatineanu; Margareta Coteata; Radovanović, Miroslav ; Stefan Potarniche; Lorelei Gherman; Irina Besliu | Article | 53M53 |
| 2012 | Investigation into the effect of the cutting parameters on the burr height in CO2 laser nitrogen cutting of AISI 304 stainless steel | Madić, Miloš ; Radovanović, Miroslav | Article | 23M23 |
| 2012 | Evaluation of ANN-BP and ANN-GA models performance in prediction mechanical properties and machinability of cast coper alloys | Radenković, Goran ; Miroslav Radenković ; Miloš Madić | Article | 23M23 |
| 2011 | Mathematical model of AWJ cutting of carbon steel S275JR based on ANN | Madić, Miloš ; Radovanović, Miroslav | Conference Paper | Mp. category will be shown later |
| 2011 | Surface roughness at abrasive jet engraving of glass parts | Laurentiu Slatineanu; Margareta Coteata; Radovanović, Miroslav ; Stefan Potarniche; Lorelei Gherman; Irina Besliu | Conference Paper | Mp. category will be shown later |
| 2011 | GA based regression estimator for traverse rate in abrasive water jet cutting | Radovanović, Miroslav ; Madić, Miloš ; Laurentiu Slatineanu | Conference Paper | Mp. category will be shown later |
| 2011 | Phenomena at Surface Abrasive Jet Machining | Laurentiu Slătineanu; Radovanović, Miroslav ; Vasile Braha; Stefan Potârniche; Margareta Coteaţă; Irina Beşliu | Conference Paper | Mp. category will be shown later |
| 2011 | The complexity of defining the quality laser cutting | Nedić, Bogdan ; Baralić, Jelena ; Radovanović, Miroslav | Conference Paper | Mp. category will be shown later |
| 2011 | Influence of abrasive material quantity on surface quality generated by abrasive water jet operation | Eugen Herghelegiu; Radovanović, Miroslav ; Gheorghe Brabie; Nicolae Catalin Tampu | Article | Mp. category will be shown later |
| 2011 | Prediction of mechanical properties and machinability of cast coper alloys using ANN approach | Madić, Miloš ; Radenković, Goran ; Radovanović, Miroslav | Conference Paper | Mp. category will be shown later |
| 2011 | Some possibilities for using DOE in setting ANN parameters: an application in modeling of abrasive waterjet cutting | Madić, Miloš ; Radovanović, Miroslav | Article | Mp. category will be shown later |
| 2011 | Metodologija modeliranja procesa obrade rezanjem primenom neuronskih mreža | Madić, Miloš ; Radovanović, Miroslav | Article | 53M53 |
| 2011 | Primena genetskog algoritma za optimizaciju obradnih procesa na primeru struganja | Petković, Dušan ; Radovanović, Miroslav | Article | 53M53 |
| 2011 | Cut quality in abrasive water jet cutting | Janković, Predrag ; Radovanović, Miroslav ; Baralić, Jelena | Conference Paper | Mp. category will be shown later |
| 2011 | Mathematical modeling and analysis of AWJ cutting of carbon steel S275JR using ANN | Madić, Miloš ; Radovanović, Miroslav | Article | Mp. category will be shown later |
| 2011 | Abrasive material for abrasive water jet cutting and their influence on cut surface quality | Janković, Predrag ; Radovanović, Miroslav ; Baralić, Jelena | Conference Paper | Mp. category will be shown later |