Researchers
Radovanović, Miroslav
Results 61-80 of 220
| Issue Date | Title | Author(s) | Type | Мp-cat. |
|---|---|---|---|---|
| 2016 | Selection of non-conventional machining processes using Analitic Hierarchy Process | Radovanović, Miroslav | Article | Mp. category will be shown later |
| 2016 | Comparison of fuzzy logic, regression and ANN laser kerf width models![]() | Madić, Miloš | Article | Mp. category will be shown later |
| 2016 | Determination of Manufacturing Process Conditions by Using MCDM Methods: Application in Laser Cutting![]() | Madić, Miloš | Article | 22M22 |
| 2015 | Possibilities of using discrete Monte Carlo method for solving machining optimization problems![]() | Madić, Miloš | Conference Paper | Mp. category will be shown later |
| 2015 | Multi-objective optimisation of laser cutting using cuckoo search algorithm![]() | Madić, Miloš | Article | Mp. category will be shown later |
| 2015 | Use of Taguchi Method and Grey Relational Analysis for Optimizing a Ram Electrical Discharge Machining Process | Slătineanu, Laurenţiu; Dodun, Oana; Coteaţă, Margareta; Mircescu, Ciprian; Beşliu, Irina; Radovanović, Miroslav | Book parts | Mp. category will be shown later |
| 2015 | Multi-objective optimization of laser cutting using ROV-based Taguchi methodology![]() | Madić, Miloš | Book parts | Mp. category will be shown later |
| 2015 | Procesor za izbor tehnoloških parametara procesa laserskog sečenja![]() | Blagojević, Vladislav | Technical reports | Mp. category will be shown later |
| 2015 | Poslovno i inženjersko odlučivanje primenom metoda višekriterijumske analize![]() | Madić, Miloš | Monograph | Mp. category will be shown later |
| 2015 | Taguchi Approach for the Optimization of Cutting Parameters in Finish Turning of Medical Stainless Steel![]() | Radovanović, Miroslav | Book parts | Mp. category will be shown later |
| 2015 | Investigation of surface roughness in abrasive water jet cutting using Shainin method | Radovanović, Miroslav | Article | Mp. category will be shown later |
| 2015 | Multi-Objective Tire Design Optimization by - Artificial Neural Networks![]() | Madić, Miloš | Conference Paper | Mp. category will be shown later |
| 2015 | ANN modeling and Pareto multi-objective optimization of process factors when CO2 laser cutting of stainless steel![]() | Madić, Miloš | Book parts | Mp. category will be shown later |
| 2015 | Laboratorijsko postrojenje za proveru upravljanja prilikom sinhronizacije pneumatskih izvršnih elemenata![]() | Blagojević, Vladislav | Technical reports | Mp. category will be shown later |
| 2015 | Optimizing factor levels based on cost in abrasive water jet cutting using GA![]() | Madić, Miloš | Book parts | Mp. category will be shown later |
| 2015 | Multicriteria choice of optimal values of process parameters for abrasive water jet cutting carbon steel | Radovanović, Miroslav | Conference Paper | Mp. category will be shown later |
| 2015 | Selection of non-conventional machining processes using the OCRA method![]() | Madić, Miloš | Article | 24+M24+ |
| 2015 | Aspects of machining parameter effect on cut quality in abrasive water jet cutting![]() | Janković, Predrag | Book parts | Mp. category will be shown later |
| 2015 | Non-conventional machining processes selection considering different performance criteria by using the MOORA method![]() | M. Madić | Article | Mp. category will be shown later |
| 2015 | Topography of surface machined by abrasive water jet cutting![]() | Baralić, Jelena | Conference Paper | Mp. category will be shown later |
