Researchers
Ivanov, Toni
Results 21-40 of 95
| Issue Date | Title | Author(s) | Type | Мp-cat. |
|---|---|---|---|---|
| 2023 | Improving airfoil performance by designed blowing | Svorcan, Jelena   ; Ivanov, Toni ; Simonović, Aleksandar | Conference Paper | Mp. category will be shown later |
| 2023 | Implicit LES Using New Slope Limiters | Mirkov, Nikola ; Peković, Ognjen ; Ivanov, Toni ; Kovačević, Aleksandar; Simonović, Aleksandar | Conference Paper | Mp. category will be shown later |
| 2023 | Application of Additive Technology and Reverse Engineering in the Realization of Damaged Obsolete Parts | Vorkapić, Miloš ; Živojinović, Danijela; Kreculj, Dragan; Ivanov, Toni ; Baltić, Marija ; Simonović, Aleksandar | Article | 22M22 |
| 2023 | Primena metodologije odzivnih površina (RSM) u cilju optimizacije eksperimentalnih parametara 3D-štampe i postizanja boljih mehaničkih performansi štampanih elemenata | Mladenović, Ivana ; Vorkapić, Miloš ; Pergal, Marija ; Ivanov, Toni ; Baltić, Marija ; Obradov, Marko ; Vasiljević Radović, Dana | Technical reports | 82  MNO za materijale i hemijske tehnologije (31.03.2023.)M82 |
| 2023 | Assembling biomaterial specimens in a mould made of thermoplastic polymer: 3-point bending test | Baltić, Marija ; Vorkapić, Miloš ; Simonović, Aleksandar ; Ivanov, Toni ; Tanović, Dragoljub | Conference Paper | Mp. category will be shown later |
| 2022 | Special Collection on advanced practices in aerospace and energy engineering | Svorcan, Jelena ; Andrić, Jelena; Čantrak, Đorđe ; Ivanov, Toni | Article | 22M22 |
| 2022 | Enhancing mechanical properties of 3D printed thermoplastic polymers by annealing in moulds | Vorkapić, Miloš ; Mladenović, Ivana ; Ivanov, Toni ; Kovačević, Aleksandar; Mohammad Sakib, Hasan; Aleksandar, Simonović ; Trajković, Isaak | Article | 22M22 |
| 2022 | Značaj komponenti 3D štampača na ukupan kvalitet izrade modela | Vorkapić, Miloš ; Ivanov, Toni ; Baltić, Marija ; Živojinović, Danijela | Conference Paper | Mp. category will be shown later |
| 2022 | Modeling, simulation and control of propeller driven seesaw system with asymmetric geometry using PID controller | Kovačević, Aleksandar; Svorcan, Jelena ; Ivanov, Toni | Conference Paper | Mp. category will be shown later |
| 2022 | Numerical analysis of a propeller in ground effect | Svorcan, Jelena ; Kovačević, Aleksandar; Ivanov, Toni ; Simonović, Aleksandar | Article | 52M52 |
| 2022 | Influence of wall layer number around brass inserts in 3D printed specimens subjected to axial pull-out force | Ivanović, Milica ; Vorkapić, Miloš ; Simonović, Aleksandar ; Ivanov, Toni ; Stamenković, Igor | Conference Paper | Mp. category will be shown later |
| 2022 | Numerical investigation of the influence of geometry on the thermal properties of a heat pipe | Ivanović, Milica ; Ivanov, Toni ; Aleksandar, Kovačević | Conference Paper | Mp. category will be shown later |
| 2022 | Numerical Analysis of o Propeller in Ground Effect | Svorcan, Jelena ; Kovačević, Aleksandar M. ; Ivanov, Toni ; Simonović, Aleksandar | Article | 52M52 |
| 2022 | Povećanje preciznosti izrade 3D štampanih delova primenom iterativne metode | Kovačević, Aleksandar; Ivanov, Toni ; Simonović, Aleksandar ; Vorkapić, Miloš | Conference Paper | Mp. category will be shown later |
| 2022 | Development of methodologies for experimental analysis of neck deformations caused by impact forces in martial arts | Milošević, Miloš ; Trajković, Isaak ; Golubović, Zorana ; Ivanov, Toni ; Mladenović, Goran M. ; Milovanović, Aleksa ; Mitrović, Nenad | Article | 22M22 |
| 2022 | Optimisation of tensile stress of poly(lactic acid) 3D printed materials using response surface methodology | Vorkapić, Miloš ; Mladenović, Ivana ; Pergal, Marija ; Ivanov, Toni ; Baltić, Marija | Article | Mp. category will be shown later |
| 2022 | The significance of 3D printing in textile-polymer composite structures realization for special purpose | Vorkapić, Miloš ; Baltić, Marija ; Ivanov, Toni ; Simonović, Aleksandar | Conference Paper | Mp. category will be shown later |
| 2021 | Algorithm for applying 3d printing in prototype realization – case: Enclosure for an industrial pressure transmitter | Vorkapić, Miloš ; Simonović, Aleksandar ; Ivanov, Toni | Book parts | Mp. category will be shown later |
| 2021 | Study of innovative subsonic ramjet | Davidović, Nikola ; Miloš, Predrag; Kolarević, Nenad ; Ivanov, Toni ; Jojić, Branislav | Book parts | Mp. category will be shown later |
| 2021 | Primer realizacije uzorka pomoću 3D štampe i analiza problema u kvalitetu | Vorkapić, Miloš ; Stajčić, Aleksandar ; Mladenović, Ivana ; Ivanov, Toni | Conference Paper | Mp. category will be shown later |