Researchers
Babić, Miroslav
Results 81-100 of 114
| Issue Date | Title | Author(s) | Type | Мp-cat. |
|---|---|---|---|---|
| 2011 | Tehnološki postupak dobijanja dvojnog hibridnog kompozita sa osnovom od A356 legure aluminijuma uz dodatak 10 mas. % čestica SiC i 1 mas. % čestica grafita | Bobić, Ilija | Technical reports | Mp. category will be shown later |
| 2011 | Microindentation of Polymethyl Methacrylate (PmMa) Based Bone Cement | Babić, Miroslav | Conference Paper | Mp. category will be shown later |
| 2011 | Continuous control as alternative route for wear monitoring by measuring penetration depth during linear reciprocating sliding of Ti6Al4V alloy | Živić, Fatima | Article | 21aM21a |
| 2011 | Tribological Potencial of Hybrid Composites Based on Zinc ond Aluminium Alloys Reinforced with SiC and Graphite Particles | Mitrović, Slobodan | Conference Paper | Mp. category will be shown later |
| 2011 | Tribology in Biomaterials Design and Selection | Živić, Fatima | Conference Paper | Mp. category will be shown later |
| 2011 | Influence of sliding speed and surface roughness on the friction coefficient and wear TiN coatings deposited at low temperature![]() | Kakaš, Damir | Conference Paper | Mp. category will be shown later |
| 2011 | Wear Behaviour of Ti6al4v Alloy Against Al2o3 under Linear Reciprocating Sliding | Zivic, F. | Article | 23M23 |
| 2011 | Effects of Al | Babic M. | Article | 21M21 |
| 2011 | A failure analysis of a massive excavator reduction gear in surface mining using vibration-based - condition monitoring | Babić, Miroslav | Article | 23M23 |
| 2011 | Design of Vehicle Road Testing Method for Determination of Brake Pads Friction Characteristics![]() | Glišović, Jasna | Article | 23M23 |
| 2011 | Interpretation of the Friction Coefficient During Reciprocating Sliding of Ti6Al4V Alloy Against Al2O3![]() | Živić, Fatima | Article | Mp. category will be shown later |
| 2010 | Wear Behavior of Composites Based on ZA-27 Alloy Reinforced by Al2O3 Particles Under Dry Sliding Condition | Babić, Miroslav | Article | 21aM21a |
| 2010 | Tribological model of the ironing process in sheet metal forming for lubricants testing | Adamović, Dragan | Article | 23M23 |
| 2010 | Coefficient of Dynamic Behaviour as Parameter for TiN Coating Condition Monitoring | Babić, Miroslav | Article | 23M23 |
| 2010 | Microstructure and mechanical properties of Zn25Al3Cu based composites with large Al2O3 particles at room and elevated temperatures | Bobić, Biljana M. | Article | 21M21 |
| 2010 | Tribometry of Materials for Bioengineering Applications | Živić, Fatima | Article | Mp. category will be shown later |
| 2010 | ICT tehnologije u funkciji podizanja efikasnosti bolonjskog procesa | Babić, Miroslav | Conference Paper | Mp. category will be shown later |
| 2010 | Tehnološki postupak dobijanja kompozita sa osnovom od AlSi7Mg0.3 (A356) legure uz dodatak sitnih čestica Al2O3 | Bobić, Ilija | Technical reports | Mp. category will be shown later |
| 2010 | Softverski paket za upravljanje programom podmazivanja - LubriMan | Babić, Miroslav | Technical reports | Mp. category will be shown later |
| 2010 | Električna metoda za kontrolu reološkog ponašanja poluočvrslih rastopa osnovnih legura i kompozita pri izvođenju reo/kompokasting postupka | Bobić, Ilija | Technical reports | Mp. category will be shown later |
